Microwave hook up

The old microwave did not. I would like to use that path to vent a new microwave.

Hook up microwave

My question — given the cavity would be only 3. I do not have the option to vent through the cabinet above. Your advice would be appreciated. Excellent video for through the roof , I need to install through the wall to outside is that video available? We want to hear from you! In addition to posting comments on articles and videos, you can also send your comments and questions to us on our contact page or at While we can't answer them all, we may use your question on our Today's Homeowner radio or TV show, or online at todayshomeowner.

Email will not be published required. As far as I know, no. While it would be possible to design such a system it would certainly require additional wall strength; sheetrock alone would never hold a microwave oven and it's contents. The microwave should be no less than 13" above the range. In addition, it should be no more than 54" above the floor - any less and it can be difficult for shorter people to use.

Sign in or sign up and post using a HubPages Network account. Comments are not for promoting your articles or other sites.

You have two problems here. But beyond that, you will have to enlarge the screw holes in the cabinet above. If there are blocks used to support the microwave, they can be moved and the existing holes re-used, but it will require a larger hole in the cabinet itself. If there are no blocks used to distribute the weight in the cabinet you will have to supply some. Was supposed to have a 3 inch cabinet filler on both sides.

Installing an Over the Range Microwave

Can the microwave be slid over a little to accommodate this or will it have to be removed and reinstalled. And what about the toggle bolts. It must fasten behind and above, and to material strong enough to hold it up. One must be able to get inside any "bulkhead" above and provide strong supports, although the wall behind needs only something along the lines of sheetrock. Given those requirements can be met, though, it shouldn't be too difficult - at worst open up the structure above or construct something, and then cover the opening after adding structural support.

Any ideas on how to install oven top microwave if there isn't a cabinet but bulkhead instead? I have seen any that shallow.

Session Timeout

Amazon lists several at or just over 15" deep, but that's about it. I suspect it will be very hard to find or impossible because that will sit it quite a ways back from the front of the range and make it difficult to load and empty. Coincidentally, I very recently did just that. The last microwave I installed lasted just one year and 5 days. Five days past the warranty period. A new one was purchased, of a different brand, and installed.

The brackets were radically different - there was no chance that the old bracket would fit the new microwave. Even if I had purchased the same manufacturer, I doubt that the bracket would have fit. The same model - maybe, but even that is in doubt. Plan on removing and replacing that old bracket. If you don't have to, well and good, but you should be prepared to do so. Thanks for the vote of confidence; I try to give instructions for someone that has never done the task before. Other product and company names shown may be trademarks of their respective owners. HubPages and Hubbers authors may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.

To provide a better website experience, dengarden. Please choose which areas of our service you consent to our doing so.

VIDEO: How to Install an Over the Range Microwave

For more information on managing or withdrawing consents and how we handle data, visit our Privacy Policy at: Installing an Over the Range Microwave Most of the time, installing an over the range microwave oven is not difficult, but each house is different, and problems can be encountered. Click thumbnail to view full-size. Incomplete or Missing Electrical Connections The task began with the removal of the old range fan unit, mounted in the place the over the range microwave oven was to occupy.

Installing the microwave supports Click thumbnail to view full-size. Installing the Microwave The first step in installing the new microwave is to attach the mounting bracket to the wall. Adjusting the blower motor Click thumbnail to view full-size. Adjusting the blower As it came from the factory, the exhaust blower in the microwave was installed to recirculate air back into the room.

Installing the Microwave The actual installation of the microwave is quite simple - the bottom rear of the microwave is set onto the small hooks on the rear bracket screwed to the wall, the plug and cord fed up inside the cabinet, and the unit tipped up into place. Installing an over the range microwave. Questions must be on-topic, written with proper grammar usage, and understandable to a wide audience.

Most microwaves must be A microwave should, ideally, Is the existing electrical the correct voltage for the microwave? Are typical exhaust fans less? The typical voltage for both is the Volts found throughout the house.

Session Timed Out

Are most cabinets sturdy enough for a Hood microwave? Are there microwaves that install on the wall only? What is the required height from stovetop to bottom of the microwave? This website uses cookies As a user in the EEA, your approval is needed on a few things. Otherwise the overhang will block access to the microwave.


  • How to Install a Microwave: 12 Steps (with Pictures) - wikiHow.
  • how to create a winning online dating profile.
  • matchmaking and marriage date?
  • Incomplete or Missing Electrical Connections.
  • scotty mccreery dating sadie robertson?
  • totally free dating site ukraine.
  • middletown ny dating.

For a microwave that requires base-of-cabinet attachments, you may need to saw off the overhang instead. Locate and drill the correct attachment holes. Follow these steps to determine which size holes to drill and where. The bottom edge of the plate should have an area covered in holes. Use a marker to draw circles in at least two holes. At least one should be completely over a wall stud to support the microwave's weight.

Locate the two or more holes along the upper edge of the microwave. Fill in these with a marker as well. Remove the mounting plate. Use the circles you drew as a guide, not the mounting plate. If your microwave came with a base of cabinet template, tape this where the microwave top will be located and drill where instructed for the power cord.

Otherwise, select a spot easily accessible by the power cord and out of the way of normal cabinet function. If there are no electrical outlets within reach of the cord, you will need to install a new electrical outlet. Do not use an extension cord. Secure the mounting plate. Have an assistant hold the mounting plate securely in the correct position as you fasten it to the wall. These will bear most of the microwave's weight, which is why they are used over the wall studs. The "wings" of the toggle screw go through the hole and pull against the wall as the screw is tightened.

Pull the mounting plate toward you while tightening toggle screws. With an assistant's help, hang the microwave onto the support tabs on the mounting plate's base. Snake the power cable through the hole drilled for this purpose before attaching the microwave. Fasten the microwave to the base of the cabinet above using screws where directed on the top template.

Tighten until the top of the microwave and the base of the cabinet are flush. Check every surface of your microwave for vents. You don't need a special model of microwave to place it on a shelf, but you do need to know where the vents are for proper installation Countertop models usually have vents on the sides and top of the microwave, but back panel vents are common as well. Place your hand near each side of the microwave to feel for blowing air. Remove the turntable and any other loose objects from inside the microwave.

This is especially wise if your cabinet is high up, since the table can easily fall out of the microwave during lifting.

How to Install an Over-the-Range Microwave

Place the microwave in a recessed cabinet or on a shelf. Make sure the vents are not flush against any surfaces or objects. There should be at least an inch of space next to each vent. Replace the turntable and plug the microwave in. If the cord will not reach or is in an inconvenient location, temporarily remove the microwave and drill a small hole in the cabinet or shelf to snake the cord through.


admin